1991 Rover 820 Turbo – J.C-T

1991 Rover 820 Turbo – James Copp-Taylor

Back in 2000, I purchased J421RRW for £800. A 1991 Rover 820Turbo. It was entertainingly quick, but it was hiding a ticking timebomb. I later learnt that some friends at the time knew about the ticking timebomb, specifically in regards to this example…..but did not think to tell me. Their silence was actually to my advantage as it led me on quite the journey with this car.

On the drive home from deepest fenland to Glastonbury…..I noted that the car seemed to rev at 2.5K RPM at 70, my previous 820 six dial cars always seemed to run at 3K RPM at 70mph, though I later realised that the 6 dial speedos were notoriously inaccurate. Anyway, I also noticed that the coolant temp gauge would fluctuate from the mid point, down to just above cold. I thought nothing of this and drove it home.

For the next six months, my mum enjoyed using it as her daily car. Her sedate driving style meant that the ticking timebomb remained hidden, until the evening I took it out for a spin. I made use of the cars forced induction and enjoyed some brisk runs to 60. Returning home, I smelt the un-mistakeable stench of antifreeze. Opening the bonnet revealed an engine bay drenched in coolant spray. The source for this ejection of coolant was a rather pronounced crack in the cylinder head, between the two cams, at the cambelt end of the engine. Apparently, ‘they all have the potential to do that….sir’.

I had recently been made redundant and had some time on my hands. This would mark my second M series head job, and second full head rebuild!. Next day, I pulled the head off the 820Turbo, stripped it down and bagged up all the valves, collets, springs…….put the tappets into a divided tray, filled with oil….numbers 1-16 and popped the contents of the head into the garage. A trip to my favourite scrapyard (Haynes of Challow), yielded a suitable head from a Mk1C 820Si. This was duly stripped and the casting sent for pressure testing and a skim.

Once the head returned, I rebuilt it using all the 820Turbo parts. I polished the valves and cleaned the pistons crowns to a dull shine. I also marvelled at how you could still see the hone marks on the 168K mile engine!. I reassembled the engine and felt a sinking feeling when it ran, but only ran on three cylinders. Isolating the cylinder in question and examining the plug, showed a very dry plug. A quick clean of the injector connector and we had an engine running smooth on all four cylinders.

Next, I ran the car for 500 miles, using a litre of oil!. I had made the mistake of not leaving a ring of carbon around the edge of each piston crown. 500 miles achieved, I retorqued the head and proceeded to put some more miles on the 820Turbo. Oil consumption dropped to near nothing.

What followed was a brake overhaul (the 820Turbo had the larger V6 front brakes) and…..my first ever attempt at topping up the rust proofing. Wherever I saw a bung, it would be filled with Waxoyl.

A few months later, I took delivery of E46TEW, my XJ40 3.6….which I own to this day. I could not keep both and was told by my parents (whom I lived with at the time)….’You can only keep one!!!’. The 820Turbo went.

Sadly, it did not live for much longer and appeared to vanish between 2003/4. In retrospect, I should have kept it…..it remains one of two 800s I’d own again, that being an early Sterling or 825i…..the other, an 820Turbo….saloon or fastback.

Using any technical methods and advice provided on our website is at your own risk. The Rover 600 & 800 Owners Club is not responsible for any issues arising from the advice given.