Rust Proofing – J.C-T.

Rover 800 Rust Proofing – James Copp-Taylor (2025)

One of my obsessions, is rust proofing. I get a lot of stick for it but the results are clear to see. My 1987 XJ40 – a pretty rust prone car, is now nearly forty years old and sporting its original sills, rear arches, floors and bulkheads. Admittedly, all the bolt on panels have been replaced at various points throughout my ownership!.

With the weather about to go through another heatwave, now is actually the best time to think about rust proofing. The 800 turns forty, next year and even the latest examples are nudging thirty years old.

Before I start, certain images have been borrowed from this thread https://autoshite.com/topic/48009-rover-827-update-mot-achieved-daily-driver/page/2/ . Credit to the original author.

So, products. every one have a favourite, but one piece of advice I can provide, is avoid waxoyl. It’s fairly cost effective but pretty outclassed by what is on offer these days. My personal go to products (and this is a personal opinion), are ‘Dinitrol’ and ‘Dynax SP50’.

So, lets start with the 800 series. Many years ago, I did complete some fairly extensive rustproofing on E636MDD, my old Sterling 2.7 . This original survivor was ripe for a good going over and provided me with the ideal canvas on which to commence a thorough rust proofing.

Ensure all brake components are covered with plastic bags, have some brake cleaner on standby to remove any spills.

Avoid spraying the exhaust if possible.

I am not a professional, so approaches may vary. This is not a guide but rather a run through of how I achieved the results I desired.

I started with a thorough wash, both over and under the car. Next, I laid down some sheeting and drove the car onto the sheeting. With the car in the air and supported on axle stands, I removed all four wheels and the front inner arch liners. Clear out any debris in this area. Best results can be achieved if you warm your rust proofing cannister in a bucket of very hot water. I liberally applied (using dinitrol spray cans at this point) a generous amount of coverage to both front under arch areas. In an ideal world, you would want to  remove the front and rear bumpers, but you can get away with using the ‘wand’ attachment and spraying up into these areas. if you suspect or observe any rot, take steps to remove and remedy this before you rust proof. Next, and a pretty quick win, was the sills.

At the rear of the car, on both sides, toward the front of the rear inner arch, you have two rubber bungs on each side. See here for an example. https://autoshite.com/uploads/monthly_2023_02/IMG_20230130_174009908.jpg.65d93291c9b8057ff16cc4bb379d1cf7.jpg

Removing these gives you access to the inner and outer sills. I found inserting a long tube, then spraying, allowed me to fully coat the inside of the sills, both inner and outer. You will want to go along the sill pinch points, once the fluid has set, and poke a feeler gauge, or similar….into the drain points, just to ensure they remain unblocked. Whilst in this area, you can give your rear inner arches a quick going over.

Back at the front of the car, you can spray inside the subframe through one of the open bolt holes, using a thin wand attachment to get maximum coverage. Running along the front inner wings, there should be a series of bungs. I’ve had some success with removing these and blasting in a bit of Dinitrol. The scuttle and air intake area is option, I just blasted the wand through one of the vent holes, but ideally you want to remove the cover and use a brush to paint some of the fluid into the cavity. Move to the middle of the car, the two box sections that run either side of the vehicle, should have some drain holes, these can be filled with rust proofing and liberally coated. I also sprayed into the gap between the exhaust heatshield and the center spine of the car, avoiding the exhaust wherever possible. I also covered the floorpan with rust proofing, attending to any surface rot along the way using a wire brush, rust convertor (Dintrols is rather effective) then some zinc based primer, before applying the dintrol.

Aim the wand over the fuel tank, and coat the area that is out of sight.

Couple of hot rot spots to pay attention to, the box sections on both sides, that accommodate the mount for the rear trailing links.

In the boot, on the underside of the boot, I covered the external floor, inside the boot and under the carpet, you will find another four rubber bungs, near the rear of the car….on both sides, these usually accomodate the factory tow bar (if fitted). If not, they can be removed and provide you with access to the rear box sections on both sides, liberally apply. The rear boot panel, there may be some access points behind the boot trim, which you can inject into. Protect any wiring with suitable covers.

Behind both side trim panels, you will find the rear inner arch tubs. In the past, I have had to weld in these areas, where the arch tub meets the boot floor (around the middle) and where the arch tub meets the floor and rear quarter panel. If these areas are clean on your example, paint in some rustproofing that you have decanted to a suitable bowl. With spray cans, I tend to just spray into the lid and using a 1 inch brush, brush onto the seams where the tub meets the floor and rear quarter panel. Be careful though, on Mk1 As and Bs, the ABS ECU lives in this area on the nearside (RHD examples), if ABS isn’t fitted, then you don’t need to worry. You could cover all the wiring with cling film, unplug and remove the ABS ECU (battery disconnected first), and covered the area with Dinitrol, for extra protection.

For me, this was a worthwhile exercise and time well spent. In the case of my XJ40, it has meant 23 years of happy ownership and a reasonably solid example. Admittedly, it never sees rain or winter salt!!

Hope someone finds this interesting, one final thing I will say…..don’t wear any clothes you care about. If you can, get some of those plastic overalls!! the stuff gets EVERYWHERE!!

Using any technical methods and advice provided on our website is at your own risk. The Rover 600 & 800 Owners Club is not responsible for any issues arising from the advice given.

Use of content from this article is subject to our Terms and Conditions which can be viewed by clicking here.

© Rover 600 & 800 Owners Club